A gas furnace that will not light, shuts off after a minute or blows cold air leaves a Studio City house cold fast. For gas furnace repair, Studio City HVAC Repair sends a technician who finds the failed part, writes the price down and repairs it only after you say yes. Ask for the written repair quote on this page and we will book the visit.
What the common gas furnace repairs cost
These are the figures for this kind of work in Studio City:
| Repair | Price |
|---|---|
| Igniter replacement | averages $219 |
| Flame sensor cleaning or replacement | $109 to $320 |
| Blower motor or capacitor work | $119 to $1,600 |
The range is wide because the part and the access decide the bill. A blower motor on a furnace in a tight closet costs more labor than a capacitor on an open wall. The written quote shows the part, the labor and the total before we start.
Anything outside that list, such as a control board or a heat exchanger finding, is quoted after the test and shown the same way.
Gas side or furnace side
Two different companies can own a gas problem, and it saves you a wait to know which.
- Gas smell: leave the house first, then call SoCalGas or 911 from outside. Do not try to find the leak yourself.
- Furnace will not light, short cycles or blows cold air: that is a furnace fault, and it is our call.
SoCalGas supplies natural gas to Studio City. The gas meter and the line up to it are theirs. The furnace, the gas valve, the igniter, the venting and everything inside the cabinet are the repair side.
What the technician checks on a gas furnace
A gas furnace has to move a lot of steps in order: the thermostat calls, the inducer starts, a pressure switch proves airflow, the igniter glows, the gas valve opens, the flame sensor confirms flame, and the blower starts. The fault sits at whichever step stops the sequence.
- No glow or no click points at the igniter or the control
- Flame lights and then drops points at the flame sensor
- Inducer that never starts, or a pressure switch that will not close, points at the venting side
- Burners lit but no warm air points at the blower or its capacitor
The technician walks the sequence, names the step that fails and shows you the part. We carry igniters, flame sensors, capacitors and blower assemblies for the brands common in Studio City.
Booking the visit
Call or use the form and say what the furnace does when the thermostat calls for heat. Tell us the brand if you know it and where the furnace sits: a closet, an attic or a garage. You get an arrival window when the visit is booked. The technician walks the sequence above, names the failed step and gives you the written price. You choose whether we fix it that visit.
Combustion safety on the visit
Any gas furnace repair includes a carbon monoxide check around the furnace and at the supply, since combustion gases belong outside. California law requires carbon monoxide alarms in homes with a fuel-burning appliance. If your alarm sounds, leave the house and call from outside.
When a repair is not the answer
Studio City HVAC Repair is a repair shop first. If the finding is a cracked heat exchanger or another failure where fixing costs more than it returns, you hear that with the replacement option written beside the repair number. Replacing a furnace is permitted work in California, issued through LADBS for City of Los Angeles neighborhoods, and the quote for that is a separate document. The heating installation page covers that job.
Where we repair furnaces
Studio City first, then Sherman Oaks, Burbank and Glendale. Our days run between Studio City, North Hollywood, Valley Village, Magnolia Park and Burbank, so same-day service is available across the east Valley. See the Studio City area page for the neighborhoods we cover, and the heating repair service page for the faults we handle.
FAQ
Can you repair my furnace today?
Same-day service is available across Studio City and the east Valley. Phones are answered 24/7, including no-heat nights.
Will I see the price before you start?
Yes. The technician names the failed part and writes the price down. The repair starts after you approve it.
The furnace clicks but never lights. What do I tell you?
Say what you hear and see: clicking, a glowing igniter, a flame that drops, or silence. That points the technician at the right part before arrival.
Do I need to call SoCalGas for a furnace that will not light?
Only if you smell gas. Then leave first and call from outside. A furnace that simply will not light is a repair call.
Do you repair furnaces of every brand?
We service all major brands. Give us the brand and the location of the furnace when you call.
Call for gas furnace repair
If the house is cold, call (877) 549-6850 and Studio City HVAC Repair will book a technician and price the repair in writing before work starts.
Need Professional HVAC Service?
Our HVAC-experienced technicians are ready to help with all your AC and heating needs. Contact Studio City HVAC Repair today for expert service throughout the the east San Fernando Valley service area.
